Electric showers are among the most affordable forms of showers, both in terms of the purchase price and operating costs, with a 10-minute shower costing as low as 20p. However, you might be wondering, “what are the guidelines to install a bathroom shower by myself?” when it comes to installing one.
It is certainly possible to install a new bathroom shower yourself if you replace an existing one. Because the power and water cables are already in place, all that’s left to do is install a new shower unit and riser rail, which is a relatively simple process. However, suppose you’re installing a new shower from the ground up. In that case, you’ll probably need to hire a plumber or an electrician from Naracoorte with a ‘Part P’ qualification they’ll know how to install, upgrade, or check the wiring to ensure it’s safe and secure.
However, confirm the kW rating before starting your shower installation. If the new shower unit has a higher wattage than the previous one, it may require an electrician since the wires may need to be altered to tolerate higher currents. If you’re unsure, it’s best to consult a specialist to be safe.
And to get that specialist electrician you go to . There you will find all kinds of home improvement ideas and support. This is a very big home improvement company. It is located in the USA.
Is It Possible For Me To Install A Shower On My Own?
Even if you’ve never installed a shower before, you’ll find that this is a project that DIYers with a modest level of experience will enjoy. Most of what you’ll need comes in shower kits that you can buy at a hardware store, whether you’re undertaking a bathtub conversion or building a new stall. The first step is to figure out the type of shower stall you want. Then, read out about the information which they are provided with shower. In the next section, we will learn how we can install a shower.
Easy Ways To Install A Shower In Washroom
So, there are two procedures for shower installation. Let’s have a look at different methods to install an Electric Bathroom Shower one by one, which is as follows:
Procedure One
- Choose a shower area that is both safe and convenient. Turn off both the water and the electricity in the shower. You can then use an electrical tester to confirm that the shower’s power source is turned off.
- Mark the locations on the wall where your shower unit will be installed. Drill holes in the wall with the appropriate masonry bit.
- Drill a new hole to accommodate the copper branch pipe that connects the showerhead to the main water valve.
- Cut the branch pipe to size and place it in the hole.
- Connect the branch pipe’s end to a stopcock. Make that the arrow indicator on the stopcock is pointing away from the rising mainline and towards the electric shower head.
- Connect the rising main pipe with a T-joint. Tighten the T-joint until it is comfortable.
- To connect the T-joint to the stopcock, cut another piece of connecting pipe. Connect the main valve to the branch pipe.
- The showerhead should be connected to the copper branch pipe.
- Attach the shower unit box to the holes you bored earlier.
- Connect the electric shower head to the shower unit with the provided flexible spray hose.
Procedure Two
- Make a hole in the ceiling with a drill.
- Attach a mounting board to the hole, and then install the pull-switch backplate to this board.
- Pass a circuit cable through the mounting board that has been mounted.
- Strip the cable to reveal one red wire, one black wire, and many bare wires at the switch.
- Glue the bare wires together. Carry out the same procedure with the ground wires. Wrap green and yellow sleeving around the intertwined wires.
- Connect the sleeved wires to the “E” terminal of the pull switch. Connect the black and red wires to the “N” and “L” terminals, respectively.
- Remove the end of the cable connected to the shower unit. There will be one each of black and red wires, as well as a bunch of bare wires.
- Green and yellow sleeving should be used to cover the naked wires.
- Connect the bare wires to the “E” terminal of the pull-switch, the black wire to the “N” terminal, and the red wire to the “L” terminal of the pull-“Mains” switch’s terminal.
After you’ve finished, run the electric shower to clear any dirt or debris from the pipes. Aside from that, run the shower at full power for a few minutes to let the air out of the system.
How Much Does It Cost To Have A Professional Electric Shower Installed?
Professional installation of an electric shower accounts for a significant portion of the total cost of a modern shower. With easy access to the cold water supply and a clear path from the shower to the shower unit (main electrical supply), even a simple structure can cost more than the shower itself. Find someone trained in plumbing and electrics to install your new electric bathroom shower. Green Star home design helps you in giving the best showers for your washrooms. Moreover, we also provide other essentials for washroom decoration, such as tiles. We always try our best to provide the best services for you and make you happy with our services.